• D-shaped replacement bit
  • Durable nickel pewter finish

$3.95

$9.95

Cable Luber

Bearing Driver Set

  • Fits bearing with 12-25mm I.D. and 32-47mm O.D.
  • Adapters can be changed quickly to accommodate a wide range of bearing combinations
  • Durable steel handle and anodized aluminum drivers
  • Can be used with a hammer or shop press
  • Laser etched adapters for easy identification
  • Comes with protective blow molded case

T-handle Set 7 pc Metric

  • Includes 8, 10, 12, 13, 14, 17, and 19mm
  • Durable nickel pewter finish
  • Deep 6-point sockets
  • Includes vinyl storage pouch
  • Manometer fluid refill for 08-0411 SyncPro carb tuner
  • Non-toxic
  • Mercury free
  • SyncPro manometer fluid refill does NOT work with older Motion Pro mercury carb synchronizers

$5.95

Rimshield 2 Rim Protector

$14.95

  • Used to inject lubricant in cable housing
  • Clamp over housing and wire allowing an aerosol can to be connected
  • Once lube runs out the far end, the cable is lubricated
  • Ideal for use with Motion Pro cable lube

D-shaped Bit for Motion Pro 08-0229

Motion Pro Tools

  • Precise four channel vacuum indicator designed specifically for intake synchronization of engines with multiple carburetors or throttle bodies (maximum vacuum rating for this tool is 40cm Hg)
  • New mercury-free design uses non-toxic fluid
  • For use with any 2, 3, or 4 cylinder four stroke motorcycles
  • Spill proof design allows tool to be stored in a horizontal or vertical position
  • Easy to read scale for precise synchronization
  • Unaffected by ambient pressure changes
  • Includes hang hook to clip onto the handlebars for easy use
  • Rugged, impact resistant ABS enclosure with convenient storage area for adapters
  • Rubber feet on enclosure bottom helps prevent sliding
  • Includes hoses, 5mm adapters, in-line restrictors and instructions
  • Optional 6mm adapters are available for use on most Yamaha models
  • Most Kawasaki models do not need adapters

All replacement accessories in stock

Master Link Clip Pliers

  • Quick and accurate alignment
  • Tool body clamps squarely to rear sprocket so the alignment rod will indicate sprocket alignment to chain

$17.95

*wheel not included

  • Replacement rivet tip
  • For use with Motion Pro 08-0058 chain rivet tool

$6.95

$6.95

  • Designed for those hard-to-reach air/fuel mixture screws on most multi-cylinder bikes
  • Straight-slot blade tip can be rotated by rotating the handle
  • Length is 17" with a 110 degree angled head to extend reach 1"
  • Tip height is adjustable, and can be set in place during use
  • Chrome vanadium tool steel
  • Compact design allows for use in confined spaces
  • Reversible ratchet
  • Comfortable grip

$9.95

T-Handle Ratchet 1/4" Drive

$4.95

17.95

Carburetor Tool w/bits

$26.95

Chain Align Tool

Adjustable Torque Wrench Adapter

$44.95

$3.95

We have many more tools and replacement parts in stock, just give us a call @ 402-592-1780 or 1-800-728-5728

  • New and improved version of original rimshield
  • Now made with genuine DuPont Zytel super tough nylon resin for unmatched strength and durability
  • Prevents rim damage from tire levers during tire changes
  • Dual raised beads facilitate inserting tire levers under tire bead and prevents tire lever from slipping
  • Won't mar wheels
  • Hand holds make it easy to insert and remove
  • Long apron protects hands and spokes
  • Sold in set of 2 pieces

402-592-1780

8415 "G" Street omaha, ne 68127
  • Used to remove exhaust pipe springs, seat or tank holding springs, cotter pins, side stand springs and other parts
  • New and improved design of the original
  • Durable 6061 aluminum with blue anodized finish and laser engraved logo
  • A must for installing Bib Mousse tubes
  • Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires
  • Hooks over spoke and pushes bead down on opposite side of tire from tire irons
  • No more fighting to keep bead down while installing off-road tires

$14.95

  • Allows for easy removal and installation of standard valve cores in tubed or tubeless valve stems
  • Perfect tool pack accessory

Valve Core Remover

SyncPro Manometer Fluid Refill

$106.95

  • Torque any fastener with a combination wrench or Allen wrench
  • Will work with 6mm (1/4") through 19mm (3/4") combination wrenches
  • Will work with 6mm and 8mm Allen wrenches
  • Heat-treated steel with a black oxide finish
  • 3/8" square drive is rated for a maximum torque of 100 ft lbs.
  • 4mm replacement chain breaker pin
  • For Motion Pro chain tool 08-0058

Vacuum Adapter 5mm

Nebraska
Motorcycle  Parts
  • Precision built tool for building, truing, and balancing wheels
  • Innovative single sided design allows easy access to spokes and nipples
  • High quality bearings allow precise wheel balancing
  • 15mm axle fits most modern street and dirt bikes and many mini bikes
  • Hub cones hold wheel firmly in place
  • Adjustable pointer for truing wheels
  • Simple folding design for easy storage when not in use
  • Can be used with dial indicators (not included)
  • Durable powder coat finish

$109.95

Replacement Rivet Tip

  • Designed to simplify installation and removal of clip-type master links
  • One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip

$21.95

Heavy Duty Spring Hook

$74.95

T-handle Spinner Hex

$25.95

Axis Truing and Balancing Stand

$53.95

4mm Replacement Pin

Beady Buddy 2 Tire Tool

  • Brass w/cap 5mm x P0.80mm
  • Can be permanently installed on motorcycles that only have a plug in the vacuum port
  • Eliminates the need to install adapters before every carburetor synchronization
  • Rubber caps are included to seal vacuum
  • Bearing mounted spinner provides faster and easier removal and installation of bolts and nuts
  • 1/4" hex drive head accepts most common driver bits
  • Magnet inside drive head holds driver bits firmly in place
  • Narrow drive head profile fits into tight spaces
  • Padded grip handle
  • Chrome vanadium handle and shaft
  • Durable chrome finish on shaft and handle
  • Blue anodized spinner with laser engraved Motion Pro logo
  • Shaft is 8" long
  • Bits not included

Pilot Screw Adjustment Tool

  • Precision made of aircraft grade aluminum and stainless steel
  • Designed for hard-to-reach areas and air/fuel mixtures screws on multi-cylinder motorcycles
  • Gear driven 1/4" hex drive
  • Includes five 1/4" hex drive bits (all 1/2" long) Straight slot, Phillips, D-shaped air/fuel mixture screw bit, 6mm hex jet bit, and 1/4" hex to 1/4" drive bit
  • Can be used with any 1/4" or 6mm hex bit
  • Strongest tool of its type on the market
  • Max torque is 60 in lbs.
  • 17.5" long
  • Replaceable drive gears

$74.95

SyncPro Carburetor Tuner

*We have the replacement bits in stock